專業的酒店標牌公司在標識制作時的基本流程和工藝！

    酒店標識制作時的配液如何配制！
    作為一些企業的標識制作的工藝是，用作蝕刻劑的是三氯化鐵溶液。它的波美濃度在蝕刻環節中非常重要，直接影響到蝕刻的速度。合適的波美濃度是38到40度之間。
測量濃度的方法是；將三氯化鐵溶液倒在細長的量杯中，插入波美計，挨著液面的數值就是它的波美濃度。

    酒店標識制作的配比濃度，現在的波美濃度是42度，有些太濃，酒店標識制作我們可以加水進行稀釋，攪拌均勻后，取樣重新進行測量。如果波美濃度太低，則可加入高濃度的三氯化鐵溶液。波美濃度調配合適后，倒入蝕刻機的箱體內，把蓋子蓋好。

   酒店標制識制作的如何開機，蝕刻機使用的是380V電源。打開電源開關，電源指示燈亮。啟動酸泵，讓三氯化鐵溶液在機器內循環，觀察溫度表最高不能超過50度。按下傳送帶開關，進行整機試運行。

    酒店標牌制作的工藝如何好，試刻這臺精密搖擺蝕刻機傳送帶可以無級調速，沖刷時間的長短可以在這里進行調整。蝕刻機運轉正常后，先在入料口放一塊試刻用的不銹鋼板，傳送帶會把它緩慢的送入機器內部。按下蝕刻開關，機器內的噴嘴就開始噴出三氯化鐵溶液，它的壓力基本上是恒定的。三氯化鐵溶液不斷地沖刷不銹鋼板的表面，溶液中的三價鐵離子快速氧化不銹鋼板，不銹鋼板就被蝕刻下去了。要如何制作就是如何開始。你就是這樣的制作公司形象化。

Professional sign company in the identification process and the production process when the basic!

     Identify how to make time with a liquid preparation!
     As some companies make the identification process is used etchant is ferric chloride solution. It's part of Baume concentration is very important in the etching, a direct impact on the speed of etching. The appropriate concentration of 38-40 Baume degrees.
 Concentration is measured; the ferric chloride solution to the slender measuring cup, insert Baume meter, it is next to the value of surface concentration of Baume.

     Identify the production ratio of the concentration, the concentration is now 42 degrees Baume, and some too strong, we can be diluted with water, mixing evenly, the sample re-measured. If Baume concentration is too low, you can add high concentrations of ferric chloride solution. Baume concentration deployment of suitable, into the etching machine cabinets, the lid cover.

    Standard system of knowledge production to boot, etching machine using a 380V power supply. Turn on the power switch, power indicator light. Start the acid pump, so that ferric chloride solution in the machine cycle, observe the thermometer may not exceed 50 degrees. Press the belt switch, the whole test run.

     How good sign production process, test swing carved this etching machine precision variable speed conveyor belt can, scouring the length of time can be adjusted here. Etching machine in normal operation, the first I put a feeding trial with engraved stainless steel plate, it will slow conveyor belt into the machine. Etching press switch, the machine began to spray nozzle ferric chloride solution, it is essentially constant pressure. Ferric chloride solution constantly scouring the surface of stainless steel plate, the solution of ferric ion rapidly oxidized stainless steel plate, stainless steel plate was etched on the go. How to make is how to begin. You are such a production company to visualize.